germatools.blogg.se - Sony firmware update mac

#SONY FIRMWARE UPDATE MAC MAC OS X#
#SONY FIRMWARE UPDATE MAC INSTALL#
#SONY FIRMWARE UPDATE MAC UPDATE#
#SONY FIRMWARE UPDATE MAC MANUAL#
#SONY FIRMWARE UPDATE MAC PASSWORD#

Adds the following FTP transfer functions:.

Allows you to transfer still images during shoot and playback operations.

When the following screen is displayed, click "Finish".The following benefits and improvements are also included in this update.

#SONY FIRMWARE UPDATE MAC UPDATE#

WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete. Note: The update process takes about fifteen minutes to complete. When the following screen is displayed, click "Run".After resetting, reconnection of the camera is verified, and the next Firmware Updater screen appears.Note: The camera screen turns off when the button is pushed. Reset the camera: On the camera, press the center of the control wheel to execute reset.To perform the firmware update, follow the steps to reset the camera.Then power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again. Stop the USB connection and click "Finish". Note: If the current version is "2.00", your camera does not need this update. If the current version is "1.00", click "Next". When the following screen is displayed, check the version number at the lower left.At the "Firmware Updater" screen, click "Next".When the updater recognizes the camera connection, the next "Firmware Updater" screen is displayed on the computer, and the camera screen displays "Follow the instructions on the computer".If the LCD screen of the camera dose not turn off, try disconnecting and reconnection the USB cable or try another USB port on the computer.

Note: When the camera is connected to the computer, the LCD screen of the camera turns off.

Connect the camera to your computer using the supplied USB cable.

Ensure the memory card is removed from the camera.

On the camera, select "MENU", "Setup","USB Connection", and then ensure "Mass Storage" is selected.

Make sure the USB Connection Setting is set to "Mass Storage".

At the "Firmware Updater" screen, please follow the instructions.

#SONY FIRMWARE UPDATE MAC PASSWORD#

At the Password prompt screen, enter the Name and Password for the administrative account, and then click "OK".

Double-click the "Firmware Updater" icon.

Note: Do not connect the camera to the computer yet.

Go to the directory where the file was downloaded and double-click the Update_DSCWX350V200.dmg.

Download the Update_DSCWX350V200.dmg file to a temporary or download directory (please note this directory for reference).

It is highly recommended that you print out these instructions for use as a reference during the installation process.

The Taskbar should be clear of applications before proceeding.

To ensure that no other program interferes with the installation, save all work and close all other programs.

IMPORTANT: Update functionality is not guaranteed with any other USB cable.

Use only the USB cable supplied with the camera.

WARNING!!: The camera may not operate properly if the power is interrupted during the update.

When performing the firmware update, it's recommended to use a fully charged NP-BX1 rechargeable battery pack.

This update can only be performed when the remaining battery level has three bars or more.

#SONY FIRMWARE UPDATE MAC MAC OS X#

IMPORTANT: For OS X version 10.10 or 10.11, please ensure the Mac OS X Driver Loader has been installed before continuing to update your firmware.

Available Hard Disk Space: 200 MB or more.

CPU: Intel® processor Note: Core™ Solo and Core Duo processors are not supported.

This update process requires the following items for proper updating:.

#SONY FIRMWARE UPDATE MAC MANUAL#

To change your settings, please refer to your computer manual or consult the manufacturer.

IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the update process.

By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed. It is not possible to return to a previous firmware version after updating this firmware. WARNING!!: This firmware update and any changes incurred by it are permanent.

#SONY FIRMWARE UPDATE MAC INSTALL#

Do not install this utility with any other model.

This utility is only for use with the DSC-WX350 cameras.